*型的北廣精儀絕緣漆漆膜擊穿強度測試儀

絕緣漆漆膜擊穿強度測試儀

型號分：10KV-200KV

滿足標準：GB/T 1408-2006 絕緣材料電氣強度試驗方法
          GB/T1695-2005 硫化橡膠工頻電壓擊穿強度和耐電壓強度試驗
          GB/T3333 電纜紙工頻電壓擊穿試驗方法
          HG/T 3330絕緣漆漆膜擊穿強度測定法
          GB12656 電容器紙工頻電壓擊穿試驗方法
          ASTM D149 固體電絕緣材料在工業電源頻率下的介電擊穿電壓和介電強度的試驗方法.

一、適用范圍及功能
主要適用于固體絕緣材料（如：塑料、橡膠、層壓材料、薄膜、樹脂、云母、陶瓷、玻璃、絕緣漆等絕緣材料及絕緣件）在工頻電壓或直流電壓下?lián)舸姸群湍碗妷旱臏y試。
本儀器由電腦控制，是我公司自主研發的全新第二代介電擊穿檢測儀器，本儀器由數字集成電路系統與軟件控制系統兩大部分構成，使升壓速率真正做到勻速、準確，并能夠準確測出漏電電流的數據。可實時繪制試驗曲線，顯示試驗數據，判斷準確，并可保存，分析，打印試驗數據。本系統能夠自動判別試樣擊穿并采集擊穿電壓數據及泄露電流，同時能夠在擊穿的瞬間電壓迅速降低自動歸零。軟件系統操作方便，性能穩定，安全可靠。

二、技術要求：
01、輸入電壓： 交流 220 V
02、輸出電壓： 交流 0--50 KV ;
               直流 0--70 KV ;（同類產品做到50kv）
03、電器容量： 3KVA
04、高壓分級： 0--50KV 全程可調（采用高精度電壓采樣器件，取消了同類廠家由于電壓采樣精度不夠必須采用高壓分級的方式）
05、升壓速率：
100 V/S 
200 V/S
 500 V/S
 1000 V/S
 2500 V/S
 3000 V/S （此項滿足標準里面極快速升壓試驗要求）
    備注：注：本產品采用的直流伺服電機加載減速機構，保證了標準里面關于極慢速試驗和極快速試驗的要求，（一般廠家為皮帶輪機構，誤差較大）保證用戶可以自由選擇升壓速率，是目前同類產品中*滿足國標對于升壓速率要求的測試設備。可以根據用戶需求設定不同的升壓速率

06、試驗方式：
           直流試驗：1、勻速升壓 2、階梯升壓 3、耐壓試驗
           交流試驗：1、勻速升壓 2、階梯升壓 3、耐壓試驗
 
注：根據不同行業的標準，我們可以根據用戶的要求，依據貴行業標準，為您定制行業標準所需的特殊測試功能。
07、電壓試驗精度： ≤ 1％
 08、電極規格：1、片材電極 ￠25mm  兩個   片材電極 ￠75mm一只
                 2、管用電極          兩個 、一套。
09、過電流保護裝置應有足夠靈敏度以保證試樣擊穿時在0.05S內切斷電源。
10、本儀器采用*的無觸點原件勻速調壓方式，淘汰同類產品中機械傳動升壓方式。
11、一次試驗可以做5個試樣。備注:（同類產品一次試驗只能做一個試樣）
12、耐壓時間設定：0-6小時（可通過軟件連續設定）

三、軟件功能:
    01、軟件平臺：WINDOWS窗口操作平臺，界面直觀，便于操作
02、曲線顯示：在實驗過程中可以動態顯示試驗曲線
03、數據導出：可以對試驗結果導入EXCEL表格
04、實驗報告：可以人為設置報告名稱，并對實驗報告進行打印
05、試驗方式：可以根據需求對直流試驗和交流試驗進行靈活選擇
06、試驗方法：可以根據需求自行選擇擊穿電壓、耐壓試驗、梯度試驗
07、參數設置：可以根據不同的試驗方式及試驗方法靈活設置所需的不同參數值
08、試樣設置：可對不同標準的試樣參數靈活設置
09、人員管理：設置用戶名及密碼，不同的操作員登入進行不同的試驗，互不影響
10、標準選擇：含有不同標準，可根據需求自行選擇
11、連續操作：連續操作試驗時，可直接在軟件里結束試驗，進行二次試驗

四、試驗方式
1、絕緣試樣空氣中擊穿或耐壓試驗
2、絕緣試樣浸油中擊穿或耐壓試驗
1、絕緣試樣空氣中階梯擊穿或耐壓試驗
2、絕緣試樣浸油中階梯擊穿或耐壓試驗
注：根據用戶要求，可定制其他試驗方式

五、安全保護：
 本儀器具有比較*的安全防護措施：
本試驗儀器電路保護控制：
九級安全防護措施： 備注:一般廠家為5級
（1） 超壓保護
（2）試驗過流保護
（3）試驗短路保護
（4）安全門開啟保護
（5）軟件誤操作保護
（6）零電壓復位保護（避免一般廠家急停斷電不復位二次試驗繼續升壓的危險）
（7）試驗結束放電保護
（8）獨立保護接地
（9）試驗結束放電保護（zui為安全的樹脂式放電棒 有效的避免了一般廠家傳統的放電方式和電磁放電干擾放電殘留現象）

北京北廣精儀儀器設備有限公司*產品：
（橡膠塑料電性能系列）電壓擊穿試驗儀，電氣強度測試儀，介電擊穿強度測定儀，電子*試驗機，體積電阻率表面電阻率測試儀，介電常數及介質損耗測試儀，漏電起痕試驗儀，水平垂直燃燒儀，橡膠低溫脆性沖擊試驗儀，熔融指數儀，熔體流動速率測定儀，塑料熱變形維卡軟化點溫度測定儀，滑動摩擦磨損試驗機，耐電弧試驗機，馬丁耐熱試驗儀，建材可燃試驗儀，球壓痕硬度計，簡支梁試驗機，電熱毯動負載試驗機，*試驗機，沖片機，啞鈴制樣機，落錘沖擊、落鏢沖擊，落球沖擊試驗機，指數儀等
（海綿泡沫系列）海綿泡沫壓陷硬度測定儀，落球回彈試驗機，海綿切割機，海綿拉伸強度試驗機，和疲勞壓陷試驗機，壓縮變形試驗機，撕裂強度，回彈率等。

售后服務及保修承諾：
多年來，我公司一直專業生產研究電氣試驗設備，經研究、摸索、總結出一套完整的產品服務保障體系，向用戶提供優質及時的售前、售中、售后服務
為創造，提高企業度，樹立企業形象，我們本著“一切追求高質量，用戶滿意為宗旨”的精神，以“*惠的價格、zui周到的服務、zui可靠的產品質量”的原則向您鄭重承諾：

一、產品質量承諾：
1、我公司保證向需方提供的設備是原廠生產的，并且出廠資料配件齊全。為保持合同設備的正常運行和維護，我公司保證提供的技術資料和圖紙是完整、清楚和正確的。
2、產品的制造和檢測均有質量記錄和檢測資料。
3、對產品性能的檢測，我們誠請用戶親臨對產品進行全過程、全性能檢查，待產品被確認合格后再裝箱發貨。

二、產品價格承諾：
1、為了保證產品的高可靠性和*性，系統的選材均選用國內或優質產品。
2、在同等競爭條件下，我公司在不以降低產品技術性能、更改產品部件為代價的基礎上，真誠以*惠的價格提供給貴方。

三：安裝調試及驗收承諾：
1、協助設備的安裝，負責設備的運輸、調試。
2、設備按訂貨技術附件進行驗收。終驗收在買方進行，對用戶提供的試樣進行試驗，并提供測試報告。
3、安裝調試同時，在儀器操作現場一次性免費培訓操作人員2-3名，該操作人員應是由需方選派的*穩定的員工，培訓后能夠對設備基本原理、軟件使用、操作、維護事項理解和應用，使人員能夠獨立操作設備對樣品進行檢測、分析，同時能進行基本的維護。

四、保修承諾：
1、設備保修一年，終身服務，一年內非人為損壞的零部件免費更換，保修期內接到用戶邀請后， zui遲響應時間為2小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法 。
2、保修期內人為損壞的零部件按采購（加工）價格收費更換。
3、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后3天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇。　
4、傳感器過載及整機電路超壓損壞不在保修范圍內。

Breakdown voltage tester - Computer Control

Model points: 10KV-200KV

Meet the standards: GB / T 1408-2006 Test method for insulating materials Electrical strength
          GB/T1695-2005 vulcanized rubber frequency voltage breakdown strength and dielectric strength test
          GB/T3333 cable paper frequency voltage breakdown test methods
          HG / T 3330 varnish film breakdown strength determination
          GB12656 capacitor paper frequency voltage breakdown test methods
          ASTM D149 Solid Electrical Insulating Materials at Commercial Power frequency dielectric breakdown voltage and dielectric strength test methods.

First, the scope and functions
Primarily applicable to solid insulating materials （such as: plastic, rubber, laminates, films, resins, mica, ceramic, glass, insulating paint and other insulating materials and insulating member） in the frequency voltage or DC voltage and resistance to voltage breakdown strength tests.
The instrument is controlled by computer, is my company developed a new second-generation dielectric breakdown testing instruments, the instrument consists of digital integrated systems and software control system composed of two parts, the boost rate truly uniform, accurate, and the ability to accuray measure the leakage current data. Real-time rendering test curve shows the test data to determine accuray, and save, analyze, print test data. The system can automatically determine and collect the sample breakdown breakdown voltage and leakage current data, and be able to quickly lower the breakdown voltage of the instant auto zero. Software system is easy to operate, stable performance, safe and reliable.

Second, the software features:
    01, the software platform: WINDOWS windows operating platform, intuitive interface, easy to operate
02, the curve shows: In the course of the experiment can dynamically display test curves
03, data export: You can import EXCEL spreadsheet on the test results
04, test report: report name can be artificially set, and lab reports for printing
05, Test Method: Test according to requirements of the DC and AC tests the flexibility to choose
06, Test Method: You can choose according to their own needs breakdown voltage, pressure test, the gradient test
07, parameter setting: according to different test methods and test methods needed flexibility to set different parameters
08, the sample settings: Standard samples for different parameters set flexibly
09, Personnel Management: Set the user name and password, different operators logged different tests, independently of each other
10, the standard options: with different standards, according to the needs of their own choice
11, continuous operation: Continuous operation test can be directly in the software end of the test, a second test

Third, the technical requirements:

01, the input voltage: AC 220 V
02, the output voltage: AC 0 - 50 KV;
               DC 0 - 70 KV; （similar products do 50kv）
03, electrical capacity: 3KVA
04, high grade: 0 - 50KV full adjustable （using high-precision voltage sampling devices similar manufacturers canceled due to the voltage must be high enough sampling accuracy hierarchical manner）
05, the boost rate:
100 V / S
200 V / S
 500 V / S
 1000 V / S
 2500 V / S
 3000 V / S （The latest standards which meet the test requirements very quickly boost）
    Note: Note: This product uses the most advanced DC servo motor load reduction mechanism to ensure that the latest standard test on the inside very slow and very fast testing of the latest requirements （general manufacturers of pulley mechanism, large errors） to ensure that users can freely select the boost rate, is currently the only product in its class to meet the national standard for the boost rate required test equipment. Set different according to user needs the boost rate

06, Test Method:
           DC test: 1, uniform step two, step step 3, the pressure test
           AC test: 1, uniform step two, step step 3, the pressure test
 
Note: Depending on the industry standard, we can according to user requirements, according to the industry standards, industry standards required for your custom special test function.
07, voltage test accuracy: ≤ 1%
 08, the electrode Specification: 1, sheet electrode ￠ 25mm ￠ 75mm two sheet electrodes a
                 2, effective electrode two, one set.
09, over-current protection device shall have sufficient sensitivity to ensure that the sample breakdown in 0.05S cut off the power within.
10, the instrument uses advanced non-contact voltage regulator original uniform way out similar products in the mechanical transmission boost mode.
11, a test can be done five specimens. Note: （a test similar products can only do one sample）
12, pressure time setting :0-6 hours （continuous setting via software）

Fourth, security protection:
 The instrument has a relatively complete safety precautions:
This test instrument control circuit protection:
Nine security measures: Note: Average manufacturers to 5
（1） overpressure protection
（2） Test Overcurrent
（3） Short-circuit protection test
（4） protect the safety door open
（5） Software misuse protection
（6） zero voltage reset protection （emergency power off to avoid general manufacturers continue to boost two trials is not reset danger）
（7） end of the test-discharge protection
（8） separate protective earthing
（9） end of the trial discharge protection （exclusive of the most secure and effective resin-firing rod manufacturers to avoid a general way the traditional discharge and electromagnetic interference discharge residue discharge phenomenon）

Fifth, test methods
1, insulation breakdown or sample the air pressure test
2, insulation breakdown or sample immersion oil pressure test
1, insulation breakdown or ladder sample air pressure test
2, insulation ladder sample immersion oil breakdown or pressure test
Note: According to user requirements, other test methods can be customized

Beijing North Canton Precision Instrument Co., Ltd. Hot products:
（Plastic and Electric Performance Series） voltage breakdown tester, electrical strength tester, dielectric breakdown strength tester, electronic universal testing machine, surface resistivity tester volume resistivity, dielectric constant and dielectric loss tester, leakage Tracking tester, horizontal and vertical burning tester, low temperature brittleness rubber impact tester, melt index tester, melt flow rate tester, plastic heat distortion temperature Vicat softening point tester, sliding friction and wear testing machine, arc resistance testing machine, Martin heat tester, combustible materials tester, ball indentation hardness tester, Charpy test machine, electric blankets dynamic load testing machine, universal testing machine, punching machine, dumbbell system prototype, drop hammer, dart impact, Falling ball impact test machine, instrument, such as index
（Sponge foam series） foam sponge hardness indentation tester, ball rebound test machine, foam cutting machine, foam tensile strength testing machine, pressure depression and fatigue testing machine, compression testing machine, tear strength, resilience rate .

Service and Warranty:
Over the years, our company has been specializing in the production of electrical test equipment, through research, exploration, summed up a complete product service support system, to provide users with high-quality and timely pre-sales, after-sales service
To create brand, enhance their visibility and establish a corporate image, our spirit of "all the pursuit of quality, customer satisfaction for the purpose of" spirit, "the most preferential prices, the most attentive service, the most reliable product quality" principle You solemn promise:

A commitment to product quality:
1, I need to provide to ensure that the original production equipment, and factory data accessories complete. In order to maintain the normal operation of the contract and maintenance of equipment, I guarantee to provide technical information and drawings are complete, clear and correct.
2, product manufacturing and testing are quality records and test data.
3, the product performance testing, we sincerely invite users to visit the product of the whole process, all performance checks, was confirmed to be eligible after the boxed product shipped.

Second, the product price promise:
1, in order to ensure high reliability and advanced systems were chosen selection of quality brand-name domestic or international.
2, in the same competitive conditions, our company not to reduce product performance, change the product on the basis of the cost of parts, in good faith in the most favorable price to your side.

Three: installation, commissioning and acceptance of commitments:
1, to assist with the installation, responsible for equipment transport and commissioning.
2, the device according to order technical annex for acceptance. Final acceptance for the purchaser, the user-supplied samples to test and provide test reports.
3, installation and commissioning while operating the instrument off-site training of operators free 2-3, the operator should be selected by the demand side of the long-term stability of staff training to the basic principles of the equipment, software, use, operation, maintenance Matters understanding and application of the device that are able to operate independently of the sample detection, analysis, and can carry out basic maintenance.

Fourth, warranty:
1, the device year warranty and lifetime service within one year of non-human damaged parts replaced free of charge during the warranty period the user received an invitation, at the latest within a response time of 2 hours, after the failure with user confirmation, I will 48 hours to send engineers to arrive at the scene for a free service, as soon as possible to identify the fault location and cause of the malfunction, failure to promptly report the reasons for users and exclusion methods.
2, man-made damaged parts during the warranty period by purchasing （processing） prices charged replacement.
3, the warranty period to continue to provide users with high-quality technical services, the user received within 3 days after repair invited to send engineers to reach users on-site repair. And enjoy the preferential treatment of purchased parts.
4, the sensor and the whole circuit overload overpressure damage is not covered under warranty.